WR-2 AM/FM-RBDS Wooden Cabinet Digital Tuning Radio (White)

I rated this radio at five stars in spite of problems with its user manual and the somewhat cumbersome procedure for enabling and disabling the alarm. Its FM reception and pleasing audio offset these problems. Several reviewers fault this radio's alarm feature for being inscrutable. After using this radio for several weeks, I realized that the source of confusion concerning this feature is the user manual; it is very badly written. The manual is harder to understand than the alarm feature on this radio is to operate. Some reviews also fault this feature for not having a dedicated alarm set/unset switch. Although I understand the reasoning for this criticism, I found that once I became familiar with setting the alarm and with enabling and disabling it, there was no confusion. If you live in an area with stations that broadcast RDS data, the WR-2 will set its clock using this data within a minute of connecting it to a power source, as long as you do not turn on the radio during this process. Otherwise, you can tune to an RDS-broadcasting station and press the hour button to set the time using the RDS data. The radio will gradually raise the volume from zero to the previous listening level at the alarm's set time: no jarring transition from quietly sleeping to skull-rattling audio. In contrast to the alarm feature, the radio's tuning features and preset operation are dead simple. Once a station is tuned using the scan button or the rotary dial, long pressing any of the preset buttons stores that station in the corresponding memory, and a simple button press tunes the radio to that station. Unfortunately, scanning works only from lower to higher frequencies unless the supplied remote control is used. That is not a significant problem, though. This radio sounds great. It isn't a high-end audio system, of course, but it sounds much better than its size would indicate. Also, it includes audio input and output RCA-type jacks on the back panel and a 3.5 mm stereo mini headphone jack on the front. It even has a 12-volt DC power jack (center pin +), presumably for use in RVs and boats. AM reception is not stellar, and the audio level on the AM broadcast band is several times lower than that of the FM band. Adjusting the volume control about ten steps higher compensates for this without introducing audio distortion. Reducing the bass setting by about four or five steps when listening to AM stations also assists in making audio more intelligible. There is a balanced external AM antenna terminal, which surely would help with reception, as does the use of inductively-coupled, capacitively-tuned AM antennas. However, at night I receive KGO 810 KHz in San Francisco, CA, about 750 miles away, with little static and no fading using only this radio's internal ferrite bar antenna. KGO is a clear channel station at night, though, so this may not be an indication of the WR-2's quality. FM reception is simply fantastic in my setup. I live in Milton, WA near the bottom of the hill in an upper floor apartment. I bought a cheap 300 Ohm twin lead folded dipole antenna, a 300 Ohm to 75 Ohm transformer, a female-to-female F-connector adapter, and a 12-foot RG-6 coaxial cable with male F-connectors at both ends for connecting to this radio. The dipole is tacked to a north-facing external wall at the ceiling in a T configuration. I twisted the down lead several times before connecting to the transformer and coiled the slack in the coaxial cable and secured the coil with zip ties. There is a toggle switch on the back of the radio for switching between the internal FM antenna and an externally connected one. It is imperative that this switch be placed in the external position for use with an external FM antenna. Otherwise, FM reception is very weak. With this setup, I receive KISM 92.9 MHz from Mount Constitution in the San Juan Islands, about 100 miles away, in full stereo. The WR-2 can decode this station's RDS data without problems on most days, and I receive 41 other FM stations clearly. The Sangean WR-2 is a pleasure to see, operate, and hear. I seek excuses to listen to this radio in my bedroom rather than watch the television in the living room. In my opinion, it is worth every penny. UPDATE: July 12, 2015 (two-and-a-half years later) This radio still works as well as it did the first time I turned it on. There are some things I feel buyers need to know to get the most from this product that the user manual and people's unrealistic expectations do not help with. First, I'll address some people's expectations of radio reception. Reviewers have given this radio poor marks for its AM reception and in some cases its FM reception. I agree with the poor marks for AM reception to a point. AM radio used to be a very much more important part of American culture, and AM stations were both more plentiful and more powerful. However, the AM antennas in older radios were also beefier. The one in this radio is not as good as the ferrite bar antennas in many older radios. I'm thinking of the GE Super Radio here, which has a great AM antenna. But there are other issues in today's AM radio reception environment that just did not exist twenty years ago. Today there is ubiquitous Wi-Fi and cellular phone service; the signal environment is very crowded. Typical homes have many more sources of AM radio interference operating in close proximity to any AM radio you may want to use. Also, many areas have power companies that offer Broadband over Power Lines (BPL) Internet service, which is known to cause severe interference to AM radio reception. Simply put, the FCC doesn't give a damn about your AM talk radio needs. Many AM radio stations are being required to operate on lower power than in years past. This combined with more sources of interference and with this radio's less than stellar ferrite bar antenna result in rather poor AM reception in many cases. Now, the criticisms of its FM reception are another matter. I read one review that said the reviewer could only pick up two stations in the San Francisco Bay Area. I'm from San Jose (South Bay) and lived there from 1959 until 2005. There are many FM stations all over that region. With a properly connected and installed FM antenna there is no way this radio will not perform to anyone's expectations. The most important circuit in a radio receiver is the antenna. This radio does not come with an adequate one for FM. You simply must buy or build a better one and connect it to the back of this radio and then place it as high as possible and oriented toward the stations you want to listen to. In my antenna system I have a twin-lead FM dipole antenna, a balun (bAlanced to UNbalanced) transformer that enables connecting the two lead wires from the (balanced) twin-lead antenna to a length of (unbalanced) RG-59 coaxial cable. I also have a female-to-female adapter to enable connecting the male coaxial connector of the balun to the male connector of the RG-59 cable. Both ends of the RG-59 cable have male connectors, so this cable connects directly to the radio's female coaxial connector. To help with unwanted signals from the down-lead that connects the antenna to the balun, I twisted the down-lead between twenty to thirty times so that it spirals down the wall I have it attached to. This helps to reject unwanted signals off the sides of the antenna. Also, to attenuate unwanted voltages on the coaxial cable from reaching the radio, I took twenty-six inches of the coaxial cable and coiled it into three turns and secured it with zip ties at three points on the resulting coil. You can read about how to do this at http://ham-radio.com/k6sti/balun.htm. Finally, I properly installed the antenna in a horizontal position near the ceiling in the room where the radio is. I don't even have it properly aimed. To pick up stations in Seattle (I am now in Lacey just east of Olympia) I should have the elements of the dipole aligned along a roughly east-west line so that the wires are broadside to the north-south direction along which Seattle and Lacey fall. I have mine facing east-west. Dipole antennas are roughly bi-directional; they pick up stations best in two opposing compass directions at once. Still, I pick up most Seattle stations without a problem and all local stations, too. Now, to address the criticisms of this radio's user interface. Some of the criticism is justified by its design and some of it is justified by its really crappy user manual. I'll try to clear up the confusion caused by its user manual, but bear in mind that I am not a technical writer. There are two rows of buttons on the front of the radio. The top row is devoted to controlling the power/sleep, band/Aux, and station presets. The bottom row is concerned with setting the time, the alarm, and all other miscellaneous functions. The only button on that row having anything to do with radio tuning is the SCAN button at the far left. Some buttons have secondary functions which are always accessed by pressing and holding down the button to activate the secondary function. For instance, the power button turns the radio on and off when it is pressed and immediately released. But when pressed and held down, it activates the sleep function and allows setting the radio to play from 120, 90, 60, 30, or 15 minutes before automatically shutting off. Similarly, the BAND button toggles the AM or FM radio bands. But when this button is pressed and held down it enables the Auxiliary function which plays whatever audio source is connected to the auxiliary connector on the back of the radio. The preset buttons (M1-M5) tune the radio to the frequency stored in their memory when pressed and immediately released. But when pressed and held down they store the currently tuned frequency in their associated memory. On the bottom row of buttons there is a SCAN button. When pressed and released it will scan the band for the next station and lock on to that station's frequency. When pressed and held it will turn off stereo reception on FM stations. It has no effect on AM stations since there is no AM stereo reception. This function behaves oddly though. It would be nice if when you turn it off it stayed turned off until you turn it back on. But it only stays turned off as long as you stay on the station you were tuned to when you turned it off and don't use preset buttons to tune to another station. I have found that it usually stays off if I manually tune using the tuning knob though. I will point out that unless you are connecting headphones or external speakers to the headphone jack, there is no good reason to receive stations on FM in stereo, and FM reception is improved when not using stereo. However, a simple improvement to this radio is to connect a pair of powered computer speakers to the headphone jack on the front of the radio. Speakers of good quality will be required to best the performance of this radio's internal speaker. Now, setting the time and the alarm. It can be done with the radio on or off, but I find it is much easier to always have the radio off when doing either of these two tasks. Setting the time and alarm is the source of most people's confusion with this radio, and the user manual just makes matters worse. If you have ever used a computer program that used modes to change how the user interface behaves and been infuriated by software like that, you will understand why some people hate this radio. An example of software that uses modes is the Vim text editor. It happens to be the editor I am using right now to type this review. It has two modes of operation: command mode and insert mode. In command mode the keyboard becomes a cockpit of command buttons that each do something different to the text in your file. In insert mode the keyboard acts like a typewriter and simply inserts text into your file. The buttons on this radio also have modes, but they are not nearly as confusing as the Vim text editor is. The key is to remember what mode you are in while trying to set the time or alarm. Next to the SCAN button is the DISPLAY button. This is the mode switching button. The default mode is time-setting mode. The radio is ready to enter time setting mode whenever the time is displayed or when dashes are displayed indicating that no time has been set. In either case, you only need this button for purposes of changing settings when setting the alarm. When you press it, the alarm time will be displayed and the alarm status will flash on and off indicating that alarm setting mode can be activated. What this does is change what will happen if you press and hold the SET button. When the time is displayed and you press and hold the SET button, the time-setting mode will be activated. When the alarm time is displayed and you press and hold the SET button, the alarm-setting mode will be activated. There is a sequence that each button is to be pressed when setting the time or the alarm time: left to right; the buttons are arranged in the order they should be pressed. They can be pressed out of order, but you will never go wrong pressing them in sequence from left to right. In the case of setting the alarm always begin by pressing the DISPLAY button, then the SET button, then the SELECT button, then the HOUR and MIN. buttons, and finally press the SET button again to complete the process and store everything needed for your wake-up alarm. The process is similar for setting the time, except that you begin with the SET button and skip the SELECT button altogether. To set the time begin with the SET button. Most buttons on this radio select a secondary function when pressed and held and perform their primary function when pressed and immediately released. This button does nothing when pressed and immediately released; it must be pressed and held to enable the buttons to its right to function for setting the time or alarm time. In this sense, the SET button acts to change the mode of the buttons to its right. Normally, the AF (Alternate Frequency) button can be used to tune to a station's alternate frequency if its RDS data supplies that information (theoretically). I have not found any stations that do this, so I have not been able to test this function. The CT button lets you set the clock on the radio using RDS data from stations that transmit a time signal with their data. One station in my area does this. I simply tune to this station and press the CT button. The time on the display flashes for up to a minute and then stops when the time signal is received, setting the clock to the exact second. Sweet. The button to the right of this one has a little car icon above it. This is the traffic information button. I have not tested this function. For my purposes these buttons are for setting the time manually and for setting the alarm. Getting back to setting the time, press and hold the SET button until the time begins to flash. Then press the HOUR and MIN. buttons to set the hour and minute. Finish by pressing and releasing the SET button to lock in your changes. Setting the alarm is only slightly different. In this case, begin at the left with the DISPLAY button. Press and release it to change to alarm setting mode. This displays the alarm time and causes the alarm status to flash. Then press and hold the SET button until the alarm time flashes to indicate that you can now set the alarm time and alarm type. Next, press the SELECT button to set the alarm type: buzzer, radio, or both. When you select either radio or radio and buzzer you can set the station you want to wake to using the band button and tuning knob or the station presets during this step. Then use the HOUR and MIN. buttons to set the alarm time. Lock in your changes by pressing and releasing the SET button. To turn off the alarm on your days off press DISPLAY, press and hold SET, then press SELECT until the alarm indicator only says alarm. Then press SET once more to lock in the change. Repeat this process again to turn it back on after your days off, using the SELECT button to set either buzzer, radio, or both. Your previously set time and station will still be stored until you change them. The snooze function on this radio is activated by pressing any button except the power button; the power button turns off the alarm until the next day. To recap: 1. DISPLAY, 2. SET, 3. SELECT, 4. HOUR, 5. MIN., and 6. SET in sequence from left to right and back to SET at the end will cycle you through setting both time and alarm. Again, you only need the DISPLAY and SELECT buttons when setting the alarm, but going from left to right and locking in your changes by pressing the SET button a final time will let you set both the time and alarm on this radio. I regularly change the alarm time and turn it on and off on weekends in the dark just by feeling from left to right to know which buttons need to be pressed next. If you prefer to see the time while listening to the radio, press the DISPLAY button. The time will remain displayed until you change stations or turn off the radio. Some of the preset buttons also have secondary functions when the radio is off that are accessed through pressing and holding them down. The M1 button will let you see the radio frequency for the alarm function. Pressing and holding this button down twice more (three times total) will cancel the radio frequency used for the alarm. The M3 button lets you change the time format from AM/PM (12 hour format) to 24 hour format. After pressing and holding the button to display the clock format, press and hold it again for eight seconds until it flashes. Then use the tuning knob to change the format. Press M3 again to lock in your change. The M5 button can be used to change the tuning step of the manual tuner. DON'T DO THIS UNLESS YOU KNOW WHY YOU WOULD NEED TO DO SO. Pressing the volume knob (yes it is also a button) lets you set the treble and bass. Successively pressing this knob cycles through treble and bass and finally back to its normal function of setting the volume. This radio continues to work well for me. It might be improved with an external AM antenna such as a Select-a-Tenna or similar product or with an external wire or ferrite bar AM antenna connected to its AM antenna terminal on the back. I don't listen to AM radio except occasionally at night to find distant stations. This radio is best as an FM radio and works adequately as an alarm clock. I would prefer a simpler interface to its alarm function, not to mention better alarm features like dual alarms and seven-day weekday/weekend alarms. It would also be better if the volume could be stored as part of the alarm settings. But I am not complaining. I've used it for two-and-a-half years as my only alarm clock without issues. That said, I think this radio shines best as a table radio either in a garage or on a shelf where a proper FM antenna can be properly installed. Given that it comes with a remote control, it can be placed somewhat out of reach and still be operated from the convenience of a chair across the room. If you don't have or need an external FM antenna, placing it on a high shelf will very likely improve reception.

After the FCC reduced the transmission wattage of the radio station I've listened to for years I had to do something. I purchased two other radios with larger antennas from a big box store. The larger antennas on those radios made no difference in reception and those radios had no external antenna connectors. After reading MANY, MANY reviews on Amazon I decided to get the Sangean WR-2 because of its classic/modern look and most importantly, it has the external antenna connectors for both AM and FM bands. Since I live in a low reception area far from town I was not surprised that the antenna included with the WR-2 had no better reception than the two radios from the big box store. I already had a rooftop TV antenna so I simply ran an RG-6 Solid Copper Core coax cable from the rooftop antenna into the WR-2 external antenna connector. (Don't forget to push the switch to the external antenna position) Without a doubt, I now have the best radio reception I have ever had. I'm picking up stations CLEARLY that I didn't even know existed. Now, as far as build quility is concerned I am very pleased. The buttons have an excellent feel with an audible click very similar to my (expensive) ham radio equipment. The display has three brightness settings plus a total off for the display. The wood which is one solid piece that has been steam bent has a very nice finish. This radio does not have a cheap plastic feel as it is quite heavy for it's size. It also has a built in 12V recepticle so you can use a battery/solar panels in case of a power outtage. Sound quility is unbelievable!! You can change the treble and bass, but I chose to leave it as it came from the factory. I do not own a B*se radio, but I have friends that do and I can honestly say that this radio sounds much better. I listen to talk radio almost exclusively and this radio is perfect for that. Just to hear what it would do with music, I tuned into a station (around 90 miles from me) that was playing Christmas music and I was just blown away by the sound quality. Unfortunately, there are three minor annoyances I have with this radio. None of which is a deal breaker for me, but I'd like to point them out in case the manufacturer is reading this. The first one is the fact that the ON/OFF switch is illuminated by a blue LED that is extremely bright and does not go out when you turn off the display at night. The second issue is the remote control. I feel that it offers decent control of the radio, but it is so thin and flimsy I'm afraid I'll break it as I tend to be a bit rough on remotes. The third issue I have is the fact that the radio does not come with the 12v power cord. I have a hunting cabin that I run 12v LED lights using a solar panel and this radio would be perfect if it included the 12v cord, but since it doesn't I've got to find one that will work. If I can, I'll be ordering another radio just for my cabin. That is how incredibly happy I am with this radio. I've noticed others complaining that the radio isn't the easiest to operate. I had no problems setting up the radio as far as setting the time and preset stations, but I did have to refer to the manual to understand all of the alarm, sleep, and auto-off features. Just a quick read and I am now able to do these things quickly and easily. For someone not accustomed to how electronics in general work the setup may be a concern. Put it this way, if you can program a VCR (man, I'm getting old)then you can easily operate this radio.

This is a comparison of the Sangean WR2 and the Tivoli Model One BT. I had intended to buy 2 Tivoli from their website, but bought one of each after testing out the Tivoli. Both units tested with the included FM antenna attached., and using the internal AM antenna. Back of cabinet ports are identical except for the types of AM antenna attachments. Here are the features graded: Sangean vs. Tivoli. FM Reception: A vs. A FM Sound Quality: A vs. A+ AM Reception: B+ vs. F AM Sound: A vs. C- Extras: Remote Control vs. BT receiver Ease of Use: B vs. A Cost: $118 vs. $200 Tivoli Pros: This is a beautiful minimalist-styled retro analog radio. There are only 3 dials set in a symmetrical face plate, embedded in a pristine wood cabinet. The FM sound quality is exceptional, and not lacking in bass, with the high ranges more notable than the Sangean. The old school analog tuner has a snug tactile sensation affording fine tuning, but will take several turns to traverse the full range of the dial. Intuitive BT can be connected without written instruction from a straight forward manual (7 pages). Tivoli Cons: The AM reception is horrible, lots of hissing static. This was a disappointment, and led to purchase of a separate AM antenna, yet to arrive. Reception and sound were better with a 20 years old clock radio; other reviewed have reported better internal antenna in older radios. Reviewers have noted a migration from AM radio, and the stations available are not vast even in a large Metro area of 2M people. Stations vary from sports, news, finance, politics, foreign languages, and religious themes. I would have preferred Tivoli sell me a FM radio with BT speaker instead of a AM/FM/BT with a diminished or ignored AM tuner thrown in. If you need AM due to your location the Tivoli might need an outdoor antenna. The dial needs a lit background. Sangean Pros: This is an excellent sounding radio with digital tuning, set in a real wood cabinet. FM sound and reception are excellent with very good AM reception using it's own internal AM antenna. It has digital tuning and 10 preset stations, which makes changing stations a breeze. The mini remote is well thought out and has all major functions. Screen brightness has 7 settings, and powers light can be turned off completely. Many clock radio functions are included, and turning off the alarm with single button press. It can be set to alarm once, daily, weekdays or weekends, again contrary to some of the reviews. Sangean Cons: Prior negative reviews centered on the display, durability, and complexity. The display is dated, with the LED set to the right instead of the center. The touted RDS is more hype than function, since the display only contains 8 letters, it had to scroll for anything lengthier. This is like trying to real a book on a stock price ticker display. I found it mostly useless since some station do not include any information on RDS. Siri can identify a song easily if you need this information. The instructions were well written, but some steps are complicated; the manual being 30 pages long. However, once it's set up I don't think you'll need to refer to the instructions much. Summary, The Sangean is reasonably priced digital tuning radio with numerous features in a smooth real wood case, and excellent sounds. The pricier Tivoli has exceptional FM sound but limited AM functionality, in a gorgeously styled wood cabinet. It might come down to convenience versus analog simplicity. The Sangean WR16 has similar features to the Tivoli M1BT but a different look

I have a number of table radios in different settings (office, home). I have a Tivoli 1 (M1), I have the Boston Acoustics (the grey plastic one), and this Sangean model WR2, that I just got. I have used them all a good deal, now. My thoughts are these. In terms of pure sound quality, for listening to FM, I think the Boston Acoustics has the best sound for music. But bummer for me, I have the BA model BEFORE they started to put the AUX input for playing mp3 player through it. I think the Tivoli has the coolest look because of the retro thing it's doing with the dial, but it does not have as good of sound as the BA or the Sangean. (at least, to my ears. The BA can really crank out base, amazingly well, for it's size.) The Tivoli seems optimized for voice, not music, but it sounds pretty good on music, too. Now, for the Sangean. I think it's the best value of these three models, at least to me. I'll list the reasons why: 1. It has a very nice and very useful remote. 2. It has tone controls nicely integrated into the volume control (you push it once to access the tone control function). 3. It has memory of radio stations. Of course, so does the BA model. The Tivoli does not, as this is the price for the cool, retro dial thing. 4. BIG ADVANTAGE. Since my BA model does not have this function at all, I'm not sure, but compared to the Tivoli (and likely the BA model), the Sangean has a huge advantage for those who want to get a stereo mini to stereo mini cable and play their MP3 player (iPod, iriver, what have you) through the table radio: That advantage is this. You can plug in the cable and leave it plugged into the radio, just plugging the other end into your MP3 player when you are ready to play it through the radio. When you want to play whatever device you have hooked up, you just plug it into the free end, press a button and hold it a moment to put the Sangean into AUX mode, and away you go. With the Tivoli (and maybe the BA, but I'm not sure), you have to physically plug and unplug the cable from the back of the radio to play in AUX mode. In other words, you cannot leave the cable plugged in, because plugging it in physically is what disables the radio and puts it into AUX mode. With the Sangean, you don't have to keep fiddling around with the back of the radio, taking the cable in and out when you want to hook up your external device; you just leave the cable in all the time and switch functions easily from the front of the unit based on what you want to do. I cannot fully describe how frustrating it is to continually be turning around the Tivoli to take the cable in or out based on whether I want to play radio or my MP3 player. CONS of the Sangean? 1. Only one that is obvious to me so far. It's noticeably larger than the Tivoli or the BA models. So, if you are interested, you'd want to think about the measurements and your space. Don't get me wrong. It's not a big radio, but it is definitely a larger unit than the other two companies put out. So, I have all three of these radios. One I use by bedside (BA). One we use in the kitchen (Tivoli). One I use at one office (Sangean). And one I use at my other office (Tivoli). I like them all. The BA, btw, has the best alarm clock controls I have ever seen. I cannot imagine a better clock radio for bedside. The Tivoli is great for listening to talk radio in the kitchen. For my other two settings, I'd swap out my other Tivoli for the Sangean any day. It just can do so much more, with amazingly logical controls, and it sounds a tad better than the Tivoli (to me). If you were holding an inpromptu dance somewhere with a table radio, get the BA. For all other general uses, I really like this Sangean.

I'm giving this a five, but I've had it for only a month, so time will ultimately tell! I needed a clock radio (or, if you prefer, a table radio with an an alarm clock) to replace a Boston Acoustics one that I loved but which didn't last nearly long enough. The BA radio still has great sound but the alarm became unreliable and it started losing time faster and faster. This one is just as good, but I hope the clock function will do better in the longevity department. I like to wake up to a clock radio with good reception and sound. For me, it sets the tone (so to speak) for the day. Static or tinny music first thing in the morning makes me grumpy. So does being awaken too abruptly. I continue to listen to it while I get dressed and so forth. So that's where I'm coming from with this. I don't do AM. I'm not concerned with attaching gadgets. As others have said, this radio has excellent sound for the price, with adjustment possible for treble and bass. I was blown away by the FM sound it had right out of the box on the internal antenna. I still haven't attached the small wire external antenna, though I do intend to do so. I haven't tried the remote control yet either. I really like the way this radio looks - it makes me happy. Its footprint is only slightly larger than the Boston Acoustics radio that I had, which is good. It has a "humane" alarm feature for both the radio and buzzer alarm. This is okay but the BA radio either started out softer or took a slightly longer time to reach full power. I liked that better, but this is adequate. The only problem I've had is that the RDS automatic time setting worked for setting the time but for 5-10 minutes or so after it first connected, it showed the time as exactly five hours earlier than it was. I found this unnerving upon waking up in the morning, so I changed it to manual and there's no problem. (I've never had any luck with this feature or with atomic-set clocks where I live.) I do like the idea of the automatic set and might try it again eventually. I find the buttons and the instruction booklet to be pretty simple and intuitive. I say that as someone who first bought a less expensive Sangean clock radio (RCR-5BK Digital AM/FM Clock Radio) that I did return to Amazon because I found it more difficult and unintuitive than I would potentially need to deal with late at night. For me, this one is much better. I think this is partly a matter of what one is used to. The WR-2 settings are similar to the the Boston Acoustics radio I was using. Either there has been some improvement in the radio's features since the earliest Amazon reviews or people were missing things. For example, the product description on Amazon as I write this seems to me to be accurate in terms of things like the length and function of the battery back up and it does have a snooze function If you're looking at this radio now, don't necessarily go by early criticisms regarding a lack of specific features..

FINAL UPDATE. Very disappointed. Sound it terrible, has virtually no treble. Tuning knob is a continual annoyance; almost unusable. Alarm is so complicated it can't be used unless you wake up 7 days a week at the same time. After over a year, I barely listen to this radio. It is just a pain. It has no redeeming value at all. UPDATE: There is a new model shipping, the WR-2(II). Unfortunately, they didn't fix the knob, but they have switched over to DSP. If they are as good as the SI boards showing up in the Tecsun and Grundig G-8, it could be good. I really can't add anything to the comments on quality or sound or useful features. Sangean has some great radios and they have some duds; this is a great radio. However, for some inexplicable reason, virtually all the good radios they make have at least one glaring flaw, usually something that annoys you every time you use it, that just makes you shake your head and wonder "Who possibly thought that was a good idea???" For this radio, the problem is the tuning knob. Some genius at Sangean decided that what we really, really, needed was a knob that was recessed so much that we would have a problem gripping it every time we tried to change to another station! I have not seen this on any other brand of table radio and, in fact, Sangean doesn't seem to think this is a universally good idea as I cannot find any of their table radios with this "great feature". As such, each and every time you tune this radio, you will be annoyed. I have two other models of Sangean radios where there is a great "feature" that annoys me every time I turn the radio on. Why do they insist on re-creating the wheel? For the life of me, I don't understand why a good company would have one really bad idea about changing something that has worked for years and years, just so they can annoy their customers. It makes no sense at all and it really ruins this radio. And you know they are able to do this right. Just look at their WR-11. So, if you want a really good table radio, with very good sound and decent reception, and solid build quality, this radio is for you, provided you only want to listen to 5 stations per band. If you tune around, or if you want to wake up at a different time on Saturday, you will be frustrated and wind up muttering under your breath every time. Be Warned.

There is an old saying, "Any device which does more that one thing will do none of them well." This is a radio. It is designed to be a good sounding radio with a remote control. Other units try to do too much and often fail to provide the basics. The FM tuner is amazing and even more amazing if you hook up the external FM antenna (which is included, don't forget to slide the switch). The AM tuner is good and I have not tried it with an external antenna. Others have complained about the FM tuner and I suspect the switch on the back for internal and external antenna was in the incorrect position when they tried their unit. The sound is very good and the 7W speaker and subwoofer easily fill a small kitchen or dining area. If you need more power, it has an 1/8" record out port on the back or headphone on the front where you could connect to a bigger system or other speakers. I am comparing the sound of this unit to more expensive bookshelf speaker systems that you would find at Sears, Radio Shack, Best Buy, or Target. The sound quality is very good and I adjusted the BASS down just a few clicks. None of the bookshelf systems, including the Sony can come close to the FM tuner on this unit and the number of stations that it can clearly tune. I put different radios in the same location for testing purposes and the Sangean PLL FM tuner outperformed them all. The wood grain finish is tasteful and the brushed aluminum faceplate is aesthetically pleasing. The front controls are nice. Many radios don't feature knobs and buttons like this one. Instead they force you to use the remote control for some features. Every feature of this unit can be accessed from the front panel. This unit will also run off of 12VDC and has a jack on the back for it which allows you to use it in an RV or outdoor setting. It needs 12VDC@1AMP to operate. Nice touch! While it does not have an iPod dock it does have an AUX IN in the back if you must use it to play a CD or listen to your MP3 player. Again, this is a radio with a really good PLL FM tuner which can lock on to a station and not drift. Unlike my other cheap radios, I can walk by this radio without it losing the station or hearing interference from other stations. Unlike my car, it can read RDS information and set the internal clock. YES!!!! Serendipity! No more setting the clock. Just turn to an RDS station and press the CT button. Wait, and magically the clock is correctly set. There is no battery backup for the clock, but the manual says it will retain it's settings and clock for 6 minutes of power outage. That means momentary power hits won't cause you to be late for work. Others have complained about the display. The unit I have has 3 different intensity settings including OFF and it remembers the settings based on the mode e.g. (Radio, Clock w/Radio OFF). For clock mode, I simply set the display to off. I do not plan to use this as a clock radio so can not comment on those features. I do not live in an area of the country with traffic alerts and can not comment on that feature. I am very pleased with the radio and at $122 @ Amazon it was a great purchase. Other family members have seen it and they would now all like one for their kitchens. Comparing this to the Bose wave radio, I feel it has a better tuner and smaller footprint. The sound it very good but limited to one speaker at 7Watts where the Bose has stereo speakers and a little more power and can fill a larger area with sound. Bottom line, if you want good radio that is well designed, looks good, and doesn't take up a lot of space this is a great choice. If you need more bells and whistles use the AUX IN for you iPod or buy a bookshelf system or Bose. Just know that the FM tuner won't be the same quality.

* Good looks and build quality * Good reception * Good sound * The remote is a nice little credit-card type one (though flawed, see below) * The radio volume slowly increases when you turn it on or when turned on by the alarm, this is a pleasant feature * If left in AUX mode, the alarm/clock radio WILL still sound (and will switch to am/fm for purposes of the radio wakeup). So this is a saving grace (as one reason I got it was to play Pandora on it, I don't need to worry about falling asleep and not switching it back to radio mode) However, THE INTERFACE STINKS. * Try coming home at 2am on a Friday night and turning off the alarm so it won't buzz on Saturday morning; you'll have to look at the manual, because the procedure for setting the alarm, or even turning it on and off, requires a whole series of unintuitive steps. * Three dedicated buttons on the remote and the radio face are for: - auto time (set time from RDS; I hope I can set the time and rely on it without a "auto time" button, maybe this is for obsessive compulsives ...), - traffic (from RDS, I live in Manhattan so this is not useful, and apparently not supported by any station so I couldn't test it), and - alternative frequency (if the chosen station broadcasts on an alternative frequency ... Uh, maybe useful in a car, but I think I can find the best signal for my preferred stations without a dedicated button, this feature also does not seem to be supported on any frequencies I've tried). These functions are of limited utility. Why there are dedicated buttons for these functions but not for turning on and off the alarm is really odd. * Alarms are stupid and limited: That is, there is no setting for weekend/weekday alarms. There is no dual alarm setting (the Boston Acoustics Receptor has both of these features). For such a "high-tech" device they really made the thing inconvenient and unhelpful. * The feature that shows the artist/title of songs is so jerky and slow it is really more annoying than anything * The screen brightness cycles through 4 settings, the lowest of which is still too bright to be placed close to the bedside. And to get from "off" to the lowest setting, it forces you to cycle through the brightest setting first, which isn't pleasant in darkness. * The presets are just stupid. There are only 10 total (5 for am and 5 for fm). Rather than cycle through the presets with a knob (like the Boston acoustics) each preset has its own button (meantime, once the presets are set, you'll never touch the largest knob on the unit - the tuning knob - again, just REALLY STUPID DESIGN). This design creates the cluttered mass of buttons on the radio while at the same time limiting total number of presets to 10. Sort of the worst of both worlds (again, the Boston Acoustics is a model of simplicity in this respect ... I had to get rid of mine because my version had no AUX in and also I like the flat top surface of the Sangean, I plugged a Sony Dash into the Sangean which I use as a Pandora radio, weather monitor and clock). * The remote is symmetrical and not backlit. In the dark, even if you memorize where some of the important buttons are (like power, volume, or presets) you can't tell which end is up so you need to turn on the light to use it. * The AC plug juts way out the back about 2 inches, so don't plan to have to pushed up flush with the wall. So, it's some nice hardware but apparently no one supervised the engineers, resulting in some really tragic and foolish design decisions. Is it really so hard to make a good sounding, easy to use clock radio?

Hice la devolución en cuanto noté que no tiene la opción de usarse con baterias.

The radio needs external antenna

La principale raison pourquoi j'ai acheté cette radio était dans l'espoir d'obtenir une meilleure réception. À cet égard mes attentes ont été totalement satisfaites. J'habite en région et auparavant j'ai toujours eu de la difficulté à capter la chaîne ICI Première 95,1 peu importe l'appareil utilisé. Or, avec le Sangean WR-2 le signal est aussi clair et fort que si j'habitais à Montréal. Et ce même en utilisant uniquement l'antenne interne; autrement dit sans avoir besoin de brancher une autre antenne à l'arrière de l'appareil. Mon autre préoccupation était le son car on dit dans les commentaires que le grave du Sangean est trop prononcé. Je sais maintenant que cela est causé par la fonction "loudness" qui amplifie les fréquences les plus basses et les plus hautes. Cependant avec le WR-2 il est possible de désactiver cette fonction afin d'obtenir un son plus naturel à un niveau d'écoute normal. Autre point important pour plusieurs personnes: la luminosité de l'écran est ajustable. Une télécommande est également fournie avec l'appareil et c'est d'ailleurs l'une des raisons pourquoi j'avais sélectionné le modèle WR-2 plutôt que les autres de la gamme Sangean qui sont très semblables mais disponibles à un prix légèrement plus bas. Sur ce modèle (WR-2) il est également possible d'ajuster individuellement le grave et les aigus, en plus de pouvoir annuler ou activer la fonction "loudness" qui est engagée par défaut. Il faut savoir aussi que comme tout appareil récent cette radio est programmable et cela peut s'avérer un exercise fastidieux pour certaines personnes. Cependant les instructions sont bien rédigées et disponibles en plusieurs langues, dont le français. Ma première impression lorsque j'ai pris l'appareil dans mes mains après avoir ouvert la boîte était qu'il s'agissait d'un appareil de grande qualité. Ce que j'apprécie le plus après quelques jours d'utilisation c'est la précision de la réception et la qualité du son.

Love this sleek,well designed radio with WONDERFUL sound quality. Beats my B**E radio handsdown. Easy to program and very nice remote. Great price point. I'm reordering for my cottage

An improvement over a Sangean model we brought several years ago, even though it has the same (WR-2) product designation.