CY USB Type C USB-C Male OTG Host Type 5.1k Resistor Adapter with Black Housing Cover DIY 24pin

If you are looking for male usb-c for custom keyboard cables, these work perfectly if you don’t need the plastic shell. The shell part is garbage but I’m still giving it 5 stars because I am not using that part in my application and they work great and easy to solder. Fitment is perfect.

This worked great for my use case, which was replacing the USB-A end of my Garmin Zumo XT mount cable with USB-C. The 5.1k resistor is necessary to signal to the USB-PD (power delivery) charger that this is a "dumb" USB device and to only provide 5 volts. If that resistor isn't there, the charger will not provide any power. Of course, if you're replacing a USB-C plug on a cable you intend to use with an actual USB-C device, you'll want to use the version without the resistor, so that the charger and device negotiate the proper voltage/current for that device using the USB-PD standard.

As far as the connector and electronics go it works. Had to figure out the correct order for the wires. My kid broke her usbc gaming mouse connector and I chose this to replace it. The wires were white, yellow, green, blue. Different than what I found online so I took apart the old connector to get that correct order. The plastic housing for this is complete crap. It doesn’t lock together and didn’t stay in place so the plug got pushed in and didn’t go into the computer. I ended up trying super glue but it didn’t stick to the plug. So I used instamorph moldable plastic to create a housing. Works great.

Good OTG connector! A must for DIYer

They work, the housing isn't held together so I have to add a bit of glue. Keep in mind these will not work for charging.

Bought these a long time ago. Finally got around to use one on a long 6 foot cloth braided cable I really liked, that had the the C end damaged. Had to expand the little rear rubber boot with a reamer and a hot gun so that it would fit over the cloth sleeving, and also enlarge the hole where the cable and the boot passed through. As some suggested on previous reviews I used a few drops of thin super glue to adhere the circuit board sleeve to the outer casing. I did screw up by shorting the ground with the data + because the insulation on the wires for the cable I used melted very easily, but since this cable is only used to charge non-smart devices it'll be fine.

On top of that, this is one of the most miserable connectors I've ever had to solder. Two contacts are through-hole (although I suppose you don't have to push the wires through), and the other two are surface mount. There's nothing holding the wires to the board besides the solder itself since the housing slides apart when you insert the plug.

Everything came together well. Basic steps in photos: 1. Put the body on the wire first. Then a flexible tail is put on the wire. Next, solder the wires to the connector. Check functionality. 2. The inner case is pushed onto the metal part of the connector and beyond. The voids are filled with hot glue. Hint - apply hot melt adhesive in a thick layer around the green board and then push the inner case. Excess hot soft glue will be cut off by the inner case during the push-in. 3. Slightly slide the inner case into the outer shell and apply a couple of drops of superglue on both sides and then push it all the way. A paper towel will come in handy to remove the extruded superglue. 4. Done. 5. In fact, the short cable is made for charging Garmin from a Samsung phone while traveling (Samsung, at least the S series performs the function of a power bank), but in this configuration, it is difficult to photograph if there is no mirror.

シリアルモニター用にコードを自作するのにシールドケーブルを使いたかったので良かったです。

Eski kullanmadığım USB kablolarını atmak yerine bu uçlarla modifiye edip kullanacağım umarım oldukça işime yarar.

plus en min 5 volt aangesloten , geeft geen spaning o de usb-c aansluiting (links Vcc en rechts GND)

Best product

Qualità non eccellente ma adeguata al prezzo. La descrizione coincide con il prodotto mentre le foto no. Nelle foto infatti non sembra possibile la connessione dati usb (data+ e data-) che invece risulta possibile sul connettore. Piccola nota negativa che potrebbe anche essere positiva: I pezzi di plastica sono lisci non presentano scanalature per incastri quindi risulta tutto libero di scorrere, anche il connettore tende scivolare rientrando nella "custodia". Questo però mi ha permesso di creare connettori che si inseriscono benissimo anche nelle prese su telefoni che spesso vengono ostacolati dalle custodie con fori piccoli. Io ho risolto egregiamente riempiendo il tutto con la colla a caldo, facilmente rimovibile con semplice alcol per pulire (nel caso si debba rimetterci mano). Basta immergere il connettore per qualche secondo nell'alcol e la colla si sgretola come farina. Prodotto consigliato