4 Way Thumb Break Holster - OWB & IWB Right Handed Leather Gun Holster - Fits Glock 17 19 22 23 32, Ruger SR9 SR22, Sig P225 P299, SW MP9 MP40, Taurus G2

Got this holster as I normally carry AIWB with a sidecar style holster. That setup does not work for occasions where I am dressed up and have a tucked in button down shirt with a suit jacket. I throw this on and ride it at 6 oclock. Very comfortable. I still have some breakin to do with the retention strap because once I unsnap it I have to move it out of the way then draw cannot just pull through it yet which really slows down access to the firearm. I elected for the retention strap as I do not trust just a leather sleeve to keep me firearm secured.Breakin process took me about 1 hour. Just threw my g19 in a plastic ziploc and began to work it into the holster twisting it every which direction. Nice secure fit that will continue to improve with use. I also grabbed some leather boot wax and gave a coat of that to help moisturize and loosen the holster up. Seemed to have worked.Hardest part I found was the belt loop holes are insanely tight and very hard to get them through the first few times. I solved this by using a solid ruler and fed that through to open the holes up a bit. I do not use the belt holes just the clip but wanted to have the option should I need it in the future.This being my backup holster for special occasions it mostly sits empty I've debated getting a replica g19 like a blue gun or airsoft that I can use to loosen it up a bit. Overall very high quality.I will by another holster from these guys for my next carry that might be for special occasions only

Start off, holster is well-made with a quality leather and looks seamless. The only issue that I found is the Glock 19 is a little bigger than the holster the fit too tight. This was causing the gun not to go all the way in so you can snap the strap.The solution is to use warm water and wet the inside of the holster and wrap your gun in plastic bags or some type of plastic (I are use a few Ziploc bags)insert the gun into the holster. Once you do this, leave the gun wrapped in plastic in the holster until almost dry This causes the leather to stretch. Once you do this, the Glock fits perfect.

Delivery quick and well packaged. The holster housed the weapon snug and snap works. The leather work is beautiful and well done. The belt loops were fun but they were snug and holds the belt/Holster combo very well not at all sloppy. I have nothing bad to say about this holster. Also holster is adapted for Cross draw, side IWB and clip to go and holster loops OWB. This holster has all the correct features for the right handed user.

S o i got this in a vain attempt to find a leather IWB holster for a cz 75 compact that was long enough to not snag the sight because it was too short. I also didn't want a holster that couldn't retain it properly. So with this holster i got a good, durable, comfortable, and effective holster for the cz compact. I will definitely be using it as my carry holster for months to years to come.However, the leather flap would not go behind the hammer or the back of the slide. No fault of the holster, since it didn't specify that it was meant for my brand of carry. The only reason i knocked off a star was because the snap-on button broke within the first few times I used the button. Other than that, great holster, cut off the flap, and now it's comfy, useful, and it can retain my cz without it falling out.

I'm a bit disappointed. I've hote several 1791 holsters, this is the first one that absolutely doesn't fit the gun I bought it for. It says it's for a Glock 19, bit it's so tight I can't even get the pistol in. I tried the break in instructions provided with the holster, and it's still impossibly tight. I have a couple other pistols that fit in it fine, so I'm not sending it back, but it doesn't work for the pistol I planned on using it for. It's a shame, it's a very nice holster, it just doesn't fit my pistol.

I have this holster on a 1-1/2" wide by over 1/4" (approximately 7mm) thick leather gun belt by "Crossbreed Holsters" and use it with a G19 Gen4. It was pretty tight at first but after massaging, reholstering, and re-belting numerous times it fits much better now. A little rubbing of black shoe polish inside helped also. The retention strap and snap fit perfect. The metal belt clip has the usual bend at the opening for IWB carry and seems that it would be secure if you can bear to wear it in that manner, the leather is very robust. I don't know all the variations of the G19 but mine has shown no wear or scuffing on the slide or frame from breaking in this holster even without using a plastic bag so maybe it has a different finish than others. I bought it for OC around the "farm", fishing trips, storing in the truck toolbox, and other various secure locations where the hard plastic and paddle type holsters would be more awkward and not offer the same coverage. Being such a well made holster I hope that it can be fitted to more specific models.

Amazing product. Works with Springfield Amory Hellcat Pro. Amazon won't let me post a photo due to community guidelines.

First off, holster is very tight. Yes, I know it has to break in and I did manage to get the gun to fit into it after a few days but still way too tight. And not just the gun, the belt slots are nearly impossible to get a belt through. Even the strong side slots were difficult to thread the belt into, I never did get a belt to go through the SOB slots. So, I tried IWB, it has a belt clip after all. No go. The belt clip has no "hook" on the bottom to grab the belt during a draw. it's actually rounded, so when you draw, the whole holster comes out. Definitely not a break in issue. This would happen even if the holster weren't so stiff and tight. A holster needs to be stiff and snug, but this is unusable. Will most likely be returning.