PERDE Headlights Compatible with GMC Sierra Yukon Denali C3 Chrome Housing Halogen Projector With Performance Lens Includes Left Driver and Right Passenger Side Headlamps Set

Look great and fit fine on 2002 Yukon. Slight grey tint, hardly noticeable. These will hold 9011 HIR bulbs without modification and come with 4 9005 bulbs pre installed.

Came as expected. They make my Yukon look like new. Love it. I had a little trouble adjusting them and aiming them. But my dad helped me out with those small issues. Other than that I love my new Denali headlights.

I love these headlights.They are a direct fit on my 2000 GMC Yukon XL SLT (NOT Denali trim).The only problem I had installing these headlights, is like most aftermarket headlights, the plastic frame that connects to the truck is made of a more flexible plastic than the OE headlights. The driver side headlight went in without trouble, but the passenger side took a little bit of coaxing with the metal fastener that hold the lights to the truck.These lights are branded Perde by TYC.The low beams have a nice and sharp cutoff because of the projectors, and the light smoke is hardly noticeable.I put a cheap set of HIDs in the low beams, and it didn't mess with the cut off, so you won't be causing a bunch of glare to oncoming traffic.I also found that these lights will take 9011 HIR bulbs without modification (you could put them in both the highs and the lows and get better light out of them).

Great lights. Made of plastic. But bulbs that come with it are garbage. First week the bulbs allmost exploded. Bulb had a big bubble comming out of it. Other than that there a great deal for the money.

I needed a projector headlight, because I wanted to use LED bulbs on my GMC Sierra. I had no interest in adding wiring for some LED accent lights. These seemed to be reasonably priced with no goofy extra LED's.These lights come with 2 9005 lights one each side, instead of one 9006 and one 9005 for high beam. The LED bulbs I bought had one of each, so I used the 9005 LED and left the 9005 halogen for my high beam. But the pattern that the projector throws has some dark and some light areas on the ground. Its a little better further out, but it's definitely not of the same quality as a OEM projector lens.It took a good bit of pulling and pushing to get the pins to fit into the new housing. But I was able to get the pins to fit to hold the projector housing to the truck.My biggest problem with these lights is they don't really fit the truck correctly. The OEM light housing has a rubber trim piece, but this one has no way for that rubber to attach. This light also leaves a large nearly 1/2 inch gap at the lower inside corner where it meets the grill. In fact, there is a significant gap all the way across the bottom, but it gets worse towards the center.

They are easy to install and really look good on my 03 Sierra. Reason for 3 stars, lack of side to side adjustment. You have to get really creative to aim them straight down the road, but it's doable. The low beam pattern is very good with QUALITY L.E.D. lights, can't say the same for the high beams, they kinda spray light everywhere not focused on the road.

Perfectly fits

Important things to know about these headlights: Ok I was ready to update the look of my truck but did not want the cheap after market projectors with the halos. I decided on these because the stock Denali lights has always been a good look! The lights arrived quickly and looked great, I was excited to install them! After the install everything looked great, I had also bought the LED signal/DRL lights to complete the facelift. Everything was great until it got dark, as soon as I went for a drive I discovered 2 problems, the biggest problem was that the driver side light was aimed way over to the right, my lane in front of me was completely dark from the center of my truck to the left almost like the left light had burned out! The other problem was the light pattern is not as smooth as the stock lights. The headlights have an up and down adjustment BUT they do not have a side to side adjustment! I really like the look of the lights and wanted to make them work so after inspecting the light housing I came up with a work around. As shown in the picture, if you remove the upper inside nut, you can add washers until the light is pointed straight. This however causes another (cosmetic) problem, after getting the adjustment right I noticed that the headlight now sticks out about an inch & a half from the hood. The picture of the light pattern is after adding the washers. So for me, I'm keeping them, If the lights were aimed better and the light pattern was better, I would have gladly awarded 5 stars but if I had known these issues beforehand, I probably wouldn't have ordered them. (They also come in a big box and returning them is probably costly)