7" inch Universal Slim Fan Push Pull Electric Radiator Cooling 12V Mount Kit Black

I recently purchased two 10" electric radiator fans for my 454 Big Block engine and I couldn't be happier with the performance. The fan blades have a 10" opening and the mounting area is 12", making them a perfect fit. These fans are high CFMs, ensuring that my engine stays cool. I have been using them for a few days and I have not experienced any overheating issues. The installation was easy and straightforward, and the fans have been running smoothly ever since. I highly recommend these 10" electric radiator fans to anyone in need of a reliable cooling solution for their vehicle. The quality construction and excellent performance make them a great value for the price. I will definitely be purchasing more of these fans for my future projects.

I use my machine in continuous mode, for hours with only short breaks. The Rato 740 / Predator 670 starts overheating if nothing is done about the heat being dumped into the center compartment by both the hydraulics and the motor. The hot interior air circulates around and is sucked up by the motor and the ignition coils (and who knows what else) starts to overheat. These fans can be mounted in the sides to exhaust that hot air. Wire them in parallel with the hydraulics fan. If that fan is automatically switched, it would probably be a good idea to install a relay so the thermostatic switch isn't handling the 15-20 amps. Even if you are using a manual switch, make sure it is one that can handle that many amps continuously, or better yet, install a relay. I have installed one, and the overheating problem is nearly solved. The regulator output voltage dropped only about 0.1V with the added load, so a second one is being installed. If you have the smaller (420) engine, one may be all you need. For the 740 / 670, two seems necessary on even a mild (mid-70s) day. Also, make sure your hydraulic cooling fan is configured correctly. Mine was spinning in the correct direction but the blades had not been turned around, so it was not moving much air (and consuming too much power). The blades are stamped with direction of rotation; also look at the curvature of the blades. Same holds true for this fan; to set up in push mode, you have to reverse the wiring AND flip the blade so it is spinning in the correct direction. I also replaced the machine's side panels with hardware cloth, to better allow air flow. If you do not run your machine continuously, this all is probably not an issue. But if you are running it more than about an hour at a stretch, compartment ventilation is highly recommended.

I use this 12 Inch fan for solar Air conditioning It works well

I installed this fan in front of my recently added trans oil cooler. I used the mounting tabs. Drilling was required but this did fit nicely. Nice fan but it has no instructions at all. Comes with springs. And clips. No clear understanding how to set the fan to push air or pull. How hard can it be to add a single page instruction sheet? Sigh! Update: Reverse wires to change fan rotation. FYI.... this fan is noisy. Not too loud if you are sitting inside but outside, it is loud. I installed a wireless switch on mine so I can turn this on while sitting in traffic. No point leaving it on when vehicle is moving.

I bought this 16" Universal Slim Electric Radiator Cooling Fan for my 2005 Ram 1500, and I’ve got to say, it works great! It moves a lot of air and really helps keep the engine temperature down, especially when I’m stuck in traffic or idling for a while. The fan is slim enough to fit easily in tight spots, and I like that it can be set up as either a push or pull fan — super handy depending on where you need it. Swapping the polarity and flipping the blades was quick and easy. Installation was pretty straightforward. The mounting kit that comes with it works fine, though the plastic ties could be a little stronger — I might upgrade those later. Just a heads-up, it doesn’t come with a relay or thermostat switch, so you’ll need to grab those separately if you want it to kick on automatically. For the price, the build quality is solid. It’s lightweight, not noisy, and the airflow is surprisingly powerful. Definitely a big improvement over my old fan. Pros: Great airflow and quiet operation Fits in tight spaces Can be used as push or pull Easy to wire up Excellent value for the money Cons: Mounting kit is okay but could be sturdier Doesn’t include relay or thermostat switch Overall, I’m really happy with this fan. It does exactly what it’s supposed to do and keeps things cool without breaking the bank. Would definitely buy again!

Used it for a homemade heat transfer from a far to hot wood stove to water tank. Sadly, I forgot to turn it on and it melted to the radiator :( Great quality otherwise though! Installation was easy, connections could be a bit better, but it really wasn't intended for what I used it for!

Perfect product

Not bad for cost

As described.

So far it’s been a great upgrade to my stock atv fan. Fit my brute force perfectly.

Bon produit soufle vraiment beaucoup semble etre asser fiable! Moteur vien vraiment chaud parcontre a voir sur le long terme ce ke sa va donner!

De très bon qualité seulement que article était pas compatibles avec ce que jamais besoin en dimensions dues le retourner

Perfectos