Horande Replacement Key Fob Cover Case fits for Range Rover Evouge Discovery Sport Velar Land Rover LR2 LR4 Jaguar XF XJ XJL XE Keyless Entry Key Fob Shell

Fits my original just fine. Looks and feels like the original equipment

My Jaguar remote, like many suffered the silicone cover separation syndrome. I thought I was doomed to purchase a new remote, although the remote worked perfectly. Enter this amazing life, and money, saver. It's very easy to fit to the old electronics in the case. A very detailed explanation is on Amazon by a previous buyer. Simply pry apart the old case and the new case, pry out the electronics very carefully from the old remote (caution is the word because if you crack the printed circuit there goes about $400 out the window). I pried gently up from the side with no pins so I could work a micro screwdriver under each retaining pin. Gently pry up and the pin will snap and do this with the other pin. Lift out the PC board and the plastic guard (be sure the pins are out of the circuit board...you should see two holes) and press the board and plastic shield gently into the new case, carefully aligning the pins with the open holes on the circuit board. You do not need to glue or otherwise secure the board inside the new case, although that can be easily done by heating a very small nail or sharp object and touching the two pins to melt the top. Again, not required, but be aware the circuit board will fall out next time you change the battery. I should mention...change the CR2032 battery at this time and your remote should be good for several years. Snap the halves together, replace your emergency key and slide the chrome piece in place. (It is a difficult tight fit so I gently tapped mine in place with a rubber mallet. ) You can use your old Jaguar or Land Rover chrome piece as I did if you wish.Can you tell which is the new and old from the picture? The original spare is on top and the new is on the bottom and it works great!

Good fit. Similar quality material to OEM.

It's a little bit hard to slide the key holding cover. but with some brute force you can do it

The exterior of the case is nice, and lightweight. that were the "good" stops. Before you are able to cost the case over your existing remote's electronic board, you FIRST have to cut off the two tabs inside of the case. If you do not cut these tabs, the case will NOT snap close. Then the silver slide cover for to hide the key is another battle. It slides off easily without the key inserted. Once you insert the key, you're going to have to exert a lot of force to get it to slide completely closed or you will have to hammer it close.You have been warned.

Very easy to assemble. Just open the existing fob by sliding the silver side down and pull off. Then open the holder as shown in their video by popping it apart with a very small screwdriver. Open the new case the same way. (though our new case came with the silver side already detached) Then, once both are opened, a couple of important notes:1. Our existing fob had an almost clear rubber gasket around the inside. Remove this and put it on the new fob case the same way. It probably wont seat itself fully until the fob is reassembled and closed.2. Comparing the two open cases, there are two plastic "pins" on one side of the inside of the new case that are removed on our existing case. In checking the board that needs to be transferred, on ours anyway, those "pins" need to be removed or else the board will be damaged when trying to close the new case. (The "pins" line up with delicate circuits on the board). They are easily snapped out of the new case with a small screwdriver.Then just transfer the circuit board (it's all one piece and not attached otherwise) and carefully snap the new case back together. It's a bit tough, but very solid once closed. Then align the silver side, (there are clasps on the sides that you can eye to which way they line up) press it into place and slide it back up. Voila! Done.Works just like the original and saved a bundle!

Great Replacement For The Original key. I have a Discovery 2015 (LR4 in USA). I bought the case, The electronics still works, just move the chip to new one, fits very well.And that’s all, the key works like the old one.Just no Land Rover logo in the back.

Just as described and definitely saved about 50% most other sellers sold 1 for $20 but I found these for around $9/each!

Good

Look very real, were easy to switch the covers from the old to these new ones. Ordered 2 and both work very well. So glad we could replace just the covers instead of order new, since issue was only cosmetic- now the key fobs look brand new again.

المنتج سيء ورديء وصلت القطعه مكسورة وغير متطابقة

I have a Jag which uses the exact same fobs as Land Rover fobs (bar for the side cover being engraved with Jaguar instead of Land Rover).I lost the metal side cover which covers the spare key blade holder.I did not want to fork over a few hundred dollars for a new fob, so I found this one. Identical replica of the fob, other than the side cover not being engraved, which is honestly a non-issue.I got the product yesterday. I did not do a full on "fob transplant" so I am keeping the fob body for when the factory fob completely disintegrates (5+ years and the rubber is already peeling off), but I put the silver side cover on, and it fit, and now I can use my original fob without losing the spare key blade.Totally recommend. For approx $30 AUD I saved myself having to fork over hundreds of dollars to the "stealership" for a new key fob.

The case didn’t fit my key fob internals. And the side metal piece doesn’t even slide in. Total flop.