Super PDR Dent Puller Kit Paintless Dent Repair Kit for Car – Slide Hammer Suction Cup and PDR Light for 98% Auto Body Dent Removal, Hail Damage & Appliance Dents or Vehicle Dent Removal

This is a great kit that includes everything you need to repair nicks and dings on your vehicle. It comes with a variety of attachment heads in different sizes and shapes, making it versatile enough to handle all kinds of situations. The size and location of the dings will determine which pulling method works best for you. The kit includes a standard hot glue gun and glue sticks to attach the pulling points. The dent puller with a squeeze handle or the bridge puller is ideal for smaller dings. For larger dings, you'll need to use multiple pulling points, or you can opt for the suction cup puller, the T-handle puller, or the slide hammer, which are better suited for bigger dents. If you're dealing with a large ding, you can start with the T-handle or slide hammer to pop the dent out, then switch to the bridge puller or squeeze handle for fine-tuning. The kit also includes a handy reflector board that quickly reveals any depressions or raised areas that need attention. There's a small hammer with a protected head for evening out high points on the surface, and an air pillow that could be useful for dents in areas like lower door panels—just inflate it behind the dent to help with the repair. The kit comes with a straightforward instruction booklet that provides a step-by-step guide for fixing dings, and a squirt bottle for alcohol, which is needed to remove the hot glue after the repair. Keep in mind that if your car is in direct sunlight, the hot surface might prevent the glue from holding properly, so it's best to work in a shaded area or a garage. Overall, this is a convenient kit for fixing dings at home and saving money.

PROBLEM: Our car had 5 fairly prominent body dings: Driver door (1), trunk lid (1), driver side rear wheel well (3). THIS TOOL: Product came packed extremely neatly and carefully. Very professional kit and includes a fairly complete set of the stuff you need. PROCESS: Degrease the dented area with alcohol. Attach one or more of the provided tabs onto the door with hot glue. Wait a few minutes for the glue to cool Use the gold anodized puller tool to exert a smooth steady outward grasp on the tab and pull the dent. HINT 1: Eventually, the glue fails, leaving a glob of hot glue on the car, but (hopefully) a smaller dent than before. You may need to repeat this process 2 or 3 times per dent.) HINT 2: The hardest part of the whole process is getting the glob of hard glue gun glop off the car once you finish HINT 3: Even glue removal is not that difficult. In between pulls, just get most of It using the scraper tool. HINT 4: I found that if I coat the blob with liquid car wax, scraped off bits do not smear around and adhere again. Like using peanut butter to remove chewing gum, the wax prevents the chunks from reattaching. Wipe again with alcohol afterward to ensure the next tab will stick. HINT 5: Some dents may pull out beyond flush. If your hot glue adheres really well, you could actually raise a small lump in the sheet metal. This is not a problem, however....a little hammer is provided and a soft tool you can use to gently pound any proud areas back down. I got them close with the tool and then rubbed a strong heavy cloth-wrapped thumb with firm pressure over the repairs, pressing heavily into the steel. This actually smoothed out the metal almost perfectly. SUMMARY For the most part, this system did a really good job. It pulled every dent outward, improving the looks of each one. DISCLAIMERS 1) We had some dents that were apparently made by some sort of pointy object. Those did not come out 100%, but they still look much shallower 2) Directions are somewhat in Chinglish, but much better organized than most and with great photos.

Very fast shipping. Double boxed. Works as designed. Other say the three-level light isn't that bright. If you are not working in direct sunlight, you won't need the light on. The reflection of the lines on the vehicle will be more than enough to see the dent imperfections. Comes with a high-capacity 18650 rechargeable battery that you can recharge when you plug the unit into any USB power supply. Unit is made of lightweight plastic but feels durable. Easy to install and use. A cost-effective solution to see a dent and remove it. Unit is about the size of a large tablet and is easy to manipulate. A good choice for your dent removal needs.

The light is useful when you can get it to work. I put in a 18560 cell and plugged in to charge. There appears to be no charging capability. So attached USB cable to a power pack. Even though the power pack was fully charged the light kept cutting out. When it works it does a great job showing you low and high spots. But the one I got didn't work most of the time so I gave up using it. The glue gun didn't work from the get go. I already had a glue gun and used mine instead. The lifter works well if you can get it onto the glue tabs. The bolt holding the mechanical parts of the lifter needs to be a little longer. Loosing it enough to get it onto the tab caused the nut to come loose and the spring loaded parts went flying across my yard. The slide hammer works faily well, but it' rather light weight.most of the time you just pull the tabs loose because the glue didn't hold without doing a thing to the dent. The clear yellowish glue worked better than the black. Stuck better than black and black was super hard to revove from vehicle and tabs. If you're working on more than just a few hail dents you're going to need more glue sticks. The pump pad didn't do a thing for my dent removal job on a rear fender. The orange sucti9n cup thing was useless. I wound up using mostly the slide hammer, yellow glue with only a few useful tabs to pull dents, and the punch with hammer to tap down the high spots. Save your money and just get these items with a decent glue gun instead of buying this kit with mostly unusable parts. BTW, PDR is hard. It takes practice and skill. Knowing where to put the glue tabs and knowing how hard to pull to avoud making high spots than have to be hammered back down. There' also some dents with sharp creases that this kit just won't get no matter what.

You might have to warm up or heat for big project.

LED are not bright enough. The extension is too short to actually be useful. The suction mechanism is sticky? like why? GoPro has perfected the suction cup and yall are using sticky early gen suction cups? Cherry on top their return option are horrible. Stay away and get a line board from elsewhere

The kit is great for the $ and you can usually catch a sale or coupon. The kit itself is good quality, nothing feels super cheap; full disclosure I have not got around to using a lot of the kit just yet. If you're just starting out, this is a great starting point and will go a long way for getting out smaller dents. Funny enough, I tried the suction cup on a large panel dent on my father's truck bed and popped it right out and the cup actually stuck really well, despite my expectations for that particular tool anyway. It comes with two types of adhesive sticks to get you started and the glue gun is perfectly fine and would compare to any budget craft store one. I have read that the glue tabs do break and this upsets people but they need to understand that they are not necessarily designed to be used multiple times no matter how much you spend on them. You can likely find packs of them by themselves relatively inexpensively and should plan on that if you have several dents you plan to work on or some really creased dents with hard lines, as those are going to require a lot more force to begin to work out.

I was not real sure this would work because it seemed hard to believe that hot glue would hold strong enough to pull a dent out. It does! I had a fairly deep ding in my door after the grand kids slammed the other car door into it. I had tried suction cups and they did not pull the ding out. I tried this PDR Tool. Hot glued the small round puller plug to the top of the ding and used the spring loaded puller. Pulled back and forth for a few times and then increased the pressure a little. The puller then pulled the plug off the door leaving the dried glue on the door/ding. When I removed the dried glue I was amazed to see that about 75% of the ding was gone! I repeated this same procedure about 5 more times and each time it removed more of the ding. The ding is now completely out. I know where it was because there was a small chip of paint that was removed from the door banging. I used a scratch remover cream I got at the auto store and it cleaned up the glue marks and reduced the appearance of the scratch/missing paint. The creme put a new plastic coat over the area and the door looks very good. I pulled 3 dents out of my truck that had been there for a long time. One dent was about 3" in diameter, another about 1.5" and the other was a ding. This tool pulled them all out and my truck looks great! Just know that you have to repeat the process several times to get the dents and dings out. I am very impressed with how this tool works.

Easy to use and works great

Silverado 2009, golpeada de granizo, pensé que quitaría las abolladuras, de todo lo que viene solo me sirvió la siliconera, el martillo, cincel y la franela, lo de más realmente no me funcionó o no supe usar las herramientas, terminé empastado y repintando el daño de la camioneta

Cumplió con todo en excelentes condiciones y muy bien empaquetado

I needed to re-apply the glue stick 4x for the dent to be mostly pulled, but otherwise a good kit.

👌